| N9EWO Review :
Japan Radio Co. JRC
NRD-545 DSP Receiver
N9EWO's Review of the Japan Radio Co. (JRC) NRD-545 DSP (HF) Receiver
User comments have been at the extremes from excellent to "really poor" with the JRC NRD-545. Of course it has more to do on how sensitive YOU are to the DSP noises (overloading) that this set can emit under certain conditions. Actually it's "Audio Recovery" , that is pulling a person's spoken word out of the mud, is quite good. This is a DSP receiver , that is DSP is used in the IF / DETECTION / AGC etc. I have owned 2 samples (plus a Sherwood test sample), all being the latest firmware.
A few off the newsgroups have indicated that I do not have my NRD-545 receiver set up correctly, so I'm hearing those noises that I have indicated below. NOT TRUE !!! I have quite enough hours using this set over the years to tell you that these sounds (DSP overloading) are no joke no matter how you adjust it. It very well depends on where you are, what antenna you are using, what time of day you use the set, signal activity/strength around the tuned frequency...etc. Many factors play in this and will not be the same for all. Again, just be aware if you plan on making a "used" purchase of one. Be sure and listen to the audio files as linked below in the review.
The last "new" NRD-545's were made in early 2008. So it's the used market now for any purchases of this model. Be sure and read the "mute" issue text at the bottom of this web page in the "green" block, it can be a real issue with some samples.
samples were tested for this report
Why a JRC NRD-545 ??
What really made me go for this receiver was the number of bandwidths that are available. Seeing a range from 10 hz to 9.99 Khz in 10 Hz steps was like..”you have to be kidding “ (ALL filters being independent of mode of course) ?? Also many of the other functions being done within the DSP, including the “Notch” and “Detection” circuits hit me as being performance pluses.
The quality of construction is in the usual JRC tradition, "excellent" inside and out. The "internal" power transformer is of good quality too, I think the same one that was used in the NRD-525 / 535. It is very quiet and normal amount of heat. No excessive buzzing sounds (unlike the power transformer in the NRD-301A, which buzzes like a hive of mad bee's, also runs very HOT).
Also JRC did a excellent job with the rest of the power supply as well. They are feeding the input voltage to the 545's regulator's at a perfect level (as was the case in the NRD-525-535 sets), so they run at a very good "warmish" temperature. I have heard of Drake not doing so well in this area with the R-8 series.....you will NOT have to resort of having to use a external DC power supply to run this receiver (as some Drake R-8x owners have done) because of excessive heat and or excessive "buzzy"noises. UPDATE : JRC changed the power transformer in later production, see green block below.
A mechanical rotary encoder is being used for the "BWC" control and has a very good feel to it. The tuning knob also has a very good feel to it, no weird play or grizzly feeling. It indeed uses a very good optical type encoder here, and at this price point it should.
Push buttons all have a OK feel and are of the "tact" switch variety. Thank goodness no "Rubber/Soft Plastic" key's ! A bit of "looseness" and key wobble which is normal using this system.Yes, the 545 has the painted pushbuttons just as it was on the NRD-535. I wish manufactures would get away from the use of painting the surface of the actual button that we will be placing our paws on. You know these could show wear and worst case this paint will get removed with use.
General ergonomics are of the usual JRC stature, superb. The “Tuning Knob” speed is much improved over the NRD-525 and 535. I can set it to the speed what I like. It was just too S-L-O-W on these other JRC”s sets. My old NRD-93 also suffered from a even slower “turtle” speed knob. More later on this , but much better JRC...thank you.
As with the NRD-525 / 535 , the NRD-545 is using a nice standard "computer type" 3-wire AC plug socket for the
power input, another great item to see.
The NRD-545's display is a Negative Type LCD and uses a Fluorescent Tube behind it (CCFL) for the backlight. But I’m a bit concerned on the life of this tube before it burns out ? It does not look like it would be easy to replace and would more than likely cost a pretty penny to have it done if one was not handy with electronics (and even if the parts can still be purchased ??).
When you first turn on the NRD-545 from a cold start, the display brightness will be dim for the first couple of minutes or so. This is normal for this type of backlighting system and is not a fault.
I wish JRC would have included at least a basic set of schematics with the set . It's another "shame on you JRC thing". All we get in the owners manual is a lousy block diagram. A step back here in my view as they used to on all other previous sets (except the NRD-345). The excuse "well just purchase the service manual" does not wash with me !
Internal "AC Power Transformer" switch made in later JRC NRD-545 samples.
I made a
note above that the internal power transformer in the NRD-545
was of high quality and made no detectable buzz/hum
noises even with it off (a very light load when off).
Well this all may have changed at bit with later
production ? John W. has told me that his early 2006
sample's transformer buzzes even with it off. It's a
minor issue with him. But it appears that JRC are using a
different AC power transformer with later samples, either
with the manufacturer or at least the style.
of the 2 internal AC power transformers that have been
used in the JRC NRD-545.
Being I have not tested
one of these new samples to "hear" how bad this
buzz may be, I have to stand neutral on this one. I guess
look for a used sample for sale that has the older "green"
transformer if this is super important to you ?
Issues with noisy power supply transformers in a receiver are a real sticking point with me and is totally unacceptable. Don't get me wrong, I love having a GOOD internal power supply in a receiver, but not if it's going to create a nasty buzz within the room. Caveat emptor if this is important to YOU !! .....Dave N9EWO
On my first NRD-545 sample, I purchased the CHE-199 VHF/UHF Converter Unit. It installed very easy with no real tools. Just a slide in board and one little coax connector that pops on fast. Well after doing the required reset, It did indeed come to life, on the display that is. As far as RF performance, it was as deaf as a french fry. This was connected to high performance antenna’s as well. It barely received my local 20 kw FM broadcasting station . For any local amateur radio signals...Nothing !!...Nada. I have heard of others with this same problem. But good news is for most folks the replacement did indeed work just fine (I did not get another one to find out for myself).
It seems that JRC just had an above average “dud” rate with the CHE-199 converter ? So if you experience “Nada” instead of your Local PD....you could have one of those bad ones ?? I hear the performance is nothing to scream about when it does work right, and I would rather not tie up a HF receiver to listen to VHF/UHF signals anyway. Better with a separate radio or scanner for this frequency coverage. Forget the CHE-199 in my view !!!
I will NOT be held responsible
for any info that is listed here
CGD-197 TCXO, Beep
Level and Adjustment.
First job I wanted to tackle after dealing with the converter DOA business , was to install the CGD-197 TCXO option (Temperature Compensated Crystal "Reference" Oscillator) . Be sure to remove the little foam strip that all JRC owners all know about which hold the boards in place during shipment. But what hit’s you the fastest is the fact that ”where are innards” ? It certainly has fewer boards than previous JRC receivers. More of the sets power is being done within the DSP so the parts count is much less.
I found that the "Beep" level was too loud for my ears. There is a "Beep Level Volume" adjustment (RV3) located on the top of the CGK-160 REF/DDS board. Of course you must have the set powered on and connected to an external speaker to make this "tweak". This is covered in the owners manual as well. Yes, I wish to have a beep feedback, but not so loud.
NOTE : If you do make this adjustment, be very careful NOT to adjust with the 2 'line output' trimmer controls by mistake that are right next to this "Beep" adjustment. Will be very hard to get these back to factory specs without test equipment. Use a flashlight and be sure that your are on the right control in the first place !!
Display a bit off.....out of the box”
This is a gremlin with tabletop HF receivers that drives me nuts, and was the first item I corrected before I put the set to real use.
On the 2 samples that I have owned , both were off out of the box by around 20 to 30 Hz. This is not a nasty problem, but if you are off by 20 hz at 5 MHz, it will be worse at 15 MHz. So if you are dead on at 15 MHz...will should also be so at 5 MHz (well it should work that way). So if you are off a bit and wish to be at least closer to dead on you need to adjust CV-1 on CGK-160 board (as indicated on page 31 of the manual). Note: The higher you do go up in frequency the more touchy the adjustment (CV-1) gets. But try and adjust using WWV at 15 MHz.
WARNING: You want to pass on this adjustment if you do not have lots of patience. It can be very time consuming and end up with it even being worse !! As usual...Doing ANY of these adjustments are done at YOUR OWN RISK !!!
I use a bit different method to achieve this adjustment than listed in the owners manual. You must use a "Strong" signal on WWV on 15.000.000 MHz as they are transmitting those nifty tones (don't try if it's weak or during a quiet periods in the hour), being selected at the "Local" SSB shift (default anyway), and using USB / LSB (NOT CW as in the manual), I turn the BWC to a W-I-D-E bandwidth of at least 6 KHz or above (might as well open it up and use 9.99 KHz). Then you are able to hear the "off beat" tones real well. Makes adjusting CV-1 much easier. Allow the set warm up at least 1 hour before you do this. Of course use a hi-fi pair of headphones or external speaker to hear the output. You should hear NO difference what-so-ever between USB and LSB when it's adjusted correctly. If you cannot hear WWV (or WWVH) well at your location..sorry to say I don't have any other idea's for you.
I will NOT be held responsible
for any info that is listed here
Now you might say well, just add the CGD-197 TCXO option and that should clear up that problem...well not quite. I have installed a couple of these and both were off, a bit closer to the stock installed reference crystal....but not by much. Still about 20 Hz off (high). I can understand how this can happen..too many factors that can throw off a part like this and it's going to vary from set to set that it is installed into, bounced around in transit as well as normal aging of the crystal itself . Remember the TCXO was standard in the old NRD-525 .
As you can see in the picture below, there is indeed a trimmer cap on the CGD-197. But how do you get to it ?? CV-1 trimmer only works on the internal reference crystal. Well it can be done (I do not have any test equipment or the extension board) , but it's the old ..PULL THE POWER PLUG FROM THE WALL SOCKET EVERY TIME !!! (THIS IS MOST IMPORTANT)...pop the CGK-160 board out..do your adjustment with the proper tool. Stick it back in and see how you did. Of course allow say 10 minutes here for the crystal to reach correct temp. You of course have to keep doing this until you get it right....huffda..!!! Time consuming is right.
Another WARNING here...this is a VERY VERY touchy variable capacitor. Again this can be a very time consuming and mind straining procedure. Avoid this if you have problems with ventures like this, leave it with it being a bit OFF.
After installing a 2
CGD-197's and these adjustments....on the second time around I
had it "Dead On" in a record 15 minutes. Now if I select
10,000.000 MHz , I actually get it. This is a big plus tuning
manual ECSS (using USB/LSB), provided the station is on frequency.
And of course I can check a station's frequency quickly and
really see if they are off which can help to ID a station.
But alas, even after an additional time period (a number of years since I installed it), it has again moved up in frequency (10 hz), so it appears a touch up every once in awhile may still be needed).
1000 Memories, 32 User Defined Functions, Memory Battery, User Defined entries a bit tricky to the novice, Speed up the BWC step.
We have 1000 memory channels available on the NRD-545. Each memory channel stores: Frequency, mode, IF Filter Bandwidth (what you have stored in the WIDE, INTER or NARROW preset buttons), AGC, ATT and Tuning Steps. It does NOT store the ECSS function. The bandwidths can also be adjusted on the fly, not having to default in the menus either (unlike so many other DSP receivers and transceivers).
For the “IF Filter Bandwidth” presets in each memory entry, it
will store the WIDE, INTER or NARROW button. So what you have
entered in these 3 presets is what will end up in the memory channels.
You can easily change these from default for the 3 bandwidth presets. My favorites are listed in the charts at the bottom of this report (no suprise that they are on the wider side). See page 9 of the owners manual for the details, but remember every mode has different default settings.
IMPORTANT USER TIP : To make the Bandwidth knob "steps"
move at a faster rate (100 hz steps vs 10 hz default) by pressing
the FUNC button and then BWC. Whew, now that's much better.
These Bandwidths defaults are changed by hitting the FUNC key then push the BANDWIDTH button that you wish to change (WIDE, INTER or NARROW), next rotate the BWC knob to your desired bandwidth and finally push ENT/kHz to seal the deal. Again, every mode has it’s own settings.
32 "User Defined" functions are found on the NRD-545. The chart at the bottom of this page covers what these are and my recommended settings . But these can be a bit confusing for PROPER entry in the NRD-545 for the “novice”. The manual is a bit confusing (at least it was to me for the first time), and if one does not do this in the correct procedure, the entries will not take. It’s a piece of cake once you get use to it.
1. First press the FUNC button, followed by ENT/kHz. You will see 001 FLASHING on the left and what ever number is stored in this User Defined entry in the middle-right.
2. Next rotate the AGC/BWC
knob to the desired entry number (number at left, it should be
flashing as you rotate it).
3. Press the ENT/kHz button again, now
the flashing number with move to the Middle (ok lets call it to
4. Rotate the AGC/BWC knob to the desired number.
ENT/kHz again. The Left number will be flashing again (this is
what will be changed when your rotate the knob).
Repeat for other entries, but when you are finished be sure to end up with the left entry numbers flashing.
6. NOW the important
part, hit the CLR button when totally finished. Maybe this is not
totally correct, but is what works for me.
IMPORTANT NOTE : With any entry like this (either “user defined” other entries) on the NRD-545, one needs to keep in mind is if you go 15 seconds without a keypad “press” or knob rotation, it will revert back to a normal display and you will need to start over. If you allow this to happen, none of the entries that you have made may not take?
“# 32” User Set-Up Function (DSP Filter)
One item that you might wish to change in the “User Set-Up Functions” right away ?
On # 32 Filter setting I made the selection as 1: DSP LOOSE filter. It is set out of the box (Default) as...0: DSP SHARP filter....I found the audio more harsh, more so with fading distortion (even with ECSS) in default "0". However "SHARP" does give slightly better audio recovery to my ears. So depends on what type of signals you are listening to? With broadcasting stations (MW or SW) "LOOSE" was better for me in the AM or ECSS modes. Using the wider bandwidths this is less of an issue.
What's that "Serial Number" business again ??
NRD-545's with a serial number of RG 04665 and above have the latest ROM firmware (both DSP and operation EPROMS). The earlier samples had dreadful audio quality. What you read in this report/review were with 2 sets that have serial numbers above RG 04665, and of course the latest firmware.
"Audio in the Ruff”...DSP Limitations ?
But the first time I really listened to the audio of this set...I was pretty sad indeed. But now that I’m more used to it’s different traits, it’s not as much of a factor and not a major quirk (but it still can be annoying depending).
The 2 types of weird sounds that the NRD-545 emits are a bit hard to explain. One being more of a burp sound, the other is of a “Tick Tick” sound.
A comment made by Chris Lobdell explains a bit more on this:
"Another flaw--and I have no idea what the cause is--is a "clicking" sound that occurs while listening in the AM mode. It does not occur on all signals, but tends to show up on signals that are moderate in strength. The clicks tend to be about two per second, and are loud enough to detract from the enjoyment of listening"
Now to be fair, these gremlins only appear on ..oh I would say 1 in 20 signals, not on all . But when it does, the DSP garbage really shows it's ugly head. 2 types of "weird" sounds !!! There was NO local interference at all when I heard thee noises and again NO NB or Notch filters were on !! ECSS was off as well. Most important...if you switch over to ECSS (manual or Auto)..most of the time (but not always) the gremlins can sometimes go away. So depending, maybe a way around it...but really should we have to hear this at all coming out of near $ 2000. communications receiver ??
|N9EWO "NRD-545 DSP Issues" MP3 Audio Files|
|"The Burp's" (0:05 sec
Vatican getting ready to sign on 7305 kHz with a dead carrier. As the signal rises and falls..this sound appears.
"DSP Tick Sound" (0:15 sec mp3 file)
This mp3 audio file shows the tick sound.
“More Audio Gremlins”
Adding to the audio blues in the virgin AM mode...fading distortion sounds very harsh than with others receivers I have ever used. Another "hard to explain" problem which I can only notice on stronger signals (and still only once in awhile) with a certain fading patterns, is what sounds like an overloaded audio signal for a second or two. Manual or Auto ECSS modes usually (but not always) clears up these problems.
|N9EWO "NRD-545 DSP Audio Distortion" MP3 Audio File|
|Here is a "mp3"
audio file that shows this audio distortion with and
without the (AM Mode) Sync- ECSS in use. The station I
used is the now defunct "Radio Villa" on 4960
kHz. Using 9.90 Khz bandwidth. First 15 seconds is with
the ECSS OFF and you can sure hear this weird breakup-distortion.
The last 15 secs is with the ECSS on (was the next tune)
and clears up the nasty sound. This distortion does NOT
show up on all signals with it off.
"NRD-545 Break-up Distortion" (0:29 secs mp3 file)
So for any AM Broadcast signals ,
you need to use ECSS (manual or automatic)...otherwise it can be
very irritating indeed. There is slight hiss coming from the audio amp
in the set too. This can be a bit annoying depending on the
speaker (or headphones) being used, but does not creep out of the
The (Sync) auto ECSS circuit in general works well, only looses lock for a split second on the worst of fades..not very often. But the best Sync-ECSS in a JRC set. As you might remember the auto ECSS circuit in the NRD-535 "D" was a awful performer. The "Sync" (Auto ECSS) in the NRD-345 is another poor circuit.
IMPORTANT USER TIP : The closer you are to the "CENTER" of the
carrier, the better it will hold lock. Do not try and use the
Sync-ECSS mode if you are not tuned correctly tuned to the center of
After a bit more experience using the Sync-ECSS on the 545, it can indeed loose lock for a split second on strong signals very deep "sharp" fades.It seems that the stronger the signal, it will have more of a chance to loose lock for that split second ?? Weird is right. This is not a serious flaw...but can be annoying on certain strong signals. More times than not, it works just fine. Sync-ECSS is still better than any previous JRC receiver.
AGC is NOT Adjustable in AM or Sync-ECSS Modes
The AD's that JRC had floating around on the NRD-545 when being sold new, indicated that the AGC decay rate was adjustable in the Sync-ECSS mode. Well if they are talking about the auto "ECSS" button/mode..they are DEAD WRONG , as it most certainly is not. It is fixed (not adjustable) just as it is in the AM mode. Yes, this is correct...you are NOT able to adjust the ACG decay rate in the AM mode with the NRD-545.
Slight Sync-ECSS "OFF" Gremlin
One note I need to pass along in regards to the Sync-ECSS mode.
IN SOME CASES, when you turn off the Sync-ECSS
and start to tune with the knob, you may notice that it may not
be totally OFF (you may hear heterodynes). So once in awhile
it can take about 5 seconds for other circuits in the ECSS
circuit chain to totally turn off. So 2 or 3 "Mississippi's"
you will hear the "het's" go away. This is not a fault
and is totally normal.
What is the "AMS" button for ?? (for you first time folks to the NRD-545), SW stereo
On the "AM" mode button, you see AMS printed along side of it. The owners manual gives very little information on what this function really does. Well first it appears to give a even wider IF bandwidth over what the normal BWC control gives at max (10 kHz). I would say about 12 kHz here, but that's a guess as no real spec's exist.
If you are tuned to stronger "in the clear" signal with no fading (say a MW station) it can make for a real aural treat. If not , well that break up distortion can create a painful experience. Also the Sync-ECSS does not work when AMS is on, so no way to tackle the problem other than to turn it off.
But the real reason for the AMS button is the fact that it toggles the AM STEREO function (Motorola C-Quam system) Again, you have no Sync-ECSS function when the AMS button is on, so is not always good news here.
Overall it's fun. However, to hear this Stereo output (also goes for FM stereo when the converter is installed), you MUST connect the L and R line outputs to a EXTERNAL amplifier (or amplified computer speakers will work too).
Of course this was intended for MW stations, but IF a SW broadcast station broadcasts a C-QUAM signal , the NRD-545 will be able to decode it. A North American pirate has actually used C-QUAM on SW from our own monitoring and works good as expected (listen here as recorded using the NRD-545). But this the only example we have heard this used so don't look for much use on SW.
Tone Control affects “Line” Output
The "Tone" control affects the "Line" audio outputs. Yes..you could have knocked me over with a slight breeze when I first discovered this. Not a bad thing here...if you have a signal in the mud and are trying make a recording of it..this can be a big plus. Now that I see after doing a bit of reading in the brochure, the tone control is indeed adjusted via the DSP chip. Good idea here and works well.
General “Volume” quirk
One little minor quirk is that on certain "Broadcast" stations that are low in the audio dept the NRD-545 seems to have a hard time keeping up . That even with the volume control at 3 o'clock, you still may not have enough audio to hear it right. So the comment we have seen made by other users (see bottom of this page)..."It can run out of volume control"..seems to be a very true statement. The very expensive (and also discontinued) JRC NRD-301A "Super Set" that I have also tested has this same trait. This is the first 2 receivers that I have ever encountered that is weird in this way ?? Again, only a minor problem that should not make you shy away from this receiver...but for the record, you now know about his.
Is that 4 or 8 ohms with the speaker output ?? , Realistic Minimus-77 External Speaker
Well could be a part of the above "volume" problem ?? Just about all JRC receivers are rated 1 Watt at 4 OHMS . Yes 4 Ohms !!! Using a 8 ohm speaker is not going to hurt a thing (other way around could be). Matter of fact the matching (and suboptimal) NVA-319 speaker is using a 8 ohm speaker inside . But the output might be cut back at least a bit using a 8 ohm speaker, where a 4 ohm might give a extra kick ?? I have not tested this, but could be something to look into ??
The only JRC set that I have noticed that is NOT listed at 4 ohms is the NRD-345. It is listed as 8 ohms. Weird to sat the least, and I'm not sure how much I want to believe this ??
But could be one of the reasons why some JRC owners (me included) have had sour luck in making some external speakers work right ??
I use a SMALLER OLDER 2-way die-cast hi-fi speaker. For me it's the Realistic Minimus-77 cat # 40-2054 from the early 90's. The tweeter helps very much here along with the larger woofer over the smaller Minimus 7 cousin. NOTE: I have tried all of Radio Shack's (including the RadioShack branded RCA ones) more later metal die-case 2-way speakers and they all required too much audio power to drive them (so that was a total bust). These older 40-2054's do not have this problem for some reason. Tip : If you hunt for one these speakers on the used market , watch out for the foam deterioration on the woofer.
"Quick Toggle" of Front End Filters
Something that I discovered that was NOT indicated in my 545's owners manual. This was on my NRD-545 with a serial number a bit over RG 06400 and may or may not exist on older or latest versions (not sure) ??
On # 24 of the "User Setup Functions", we have a selection for front end filtering . This allows you to bypass the front end filters for perhaps a bit more sensitivity in cases where you need every bit to pull a signal out of the mud. Normally front end filters (preselector filtering) can give a few db's of signal loss. But of course you should NOT leave this in the bypassed mode for normal listening. The NRD-525's and 535's also have the same "pass" switch.
But during "scan" (scanning of the memories) function, leaving these filters on and as it chuffs over the memory channels...well it makes the filter relays chatter like a old car on it's last legs.
So to switch off the front end filters you have to dread to the "user setup function" mode. Select it down to # 24, and then switch it to 0. Of course after you are done with your scanning, you have to do this chore all over again.
Well here is the "quick toggle" that I discovered. Press the "FUNC" (function) key then the "ATT" key. You will hear one beep (not the usual error beeps). You will see NO indication on the display anywhere, even if you drop into the user setup mode and peek at # 24 after you do this, it will not show it correctly. To toggle it back, just repeat "FUNC" and "ATT" again.
If you turn off the set and turn it back on again, it will default to whatever you have set in # 24. This quick toggle operation will not change this setting in any way.
I miss the "pass" indication on the display with the NRD-545. The NRD-525 and 535 had this of course.
(N9EWO with another neat finding on a JRC receiver. Remember the 99.999.99 entry with the NRD-535 ,as listed in October 1991 Monitoring Times page 107 ..."Display Test Mode" . The NRD-545 display mode is selected by while pressing and holding the FUNC + DIMMER buttons , then power the receiver up. To switch back to normal mode, just rotate the tuning knob.)
I love the IF bandwidths adjustable up to 10 kHz (or more). I hate receivers that stop at 6~8 kHz which seems to be the trend these days !
So what's the word ?? Discontinued Receiver.
The AGC configuration and adjustments with the 545 is excellent for SSB signals. AM mode with the "lone" fixed AGC is not as stellar , but is most usable for the most part. SSB audio actually sounds much cleaner and less hisser than with the AOR AR7030.
After reading these comments you are wondering if I'm totally against this set ? No. I actually enjoy the NRD-545 very much. Maybe I'm just getting used to it's strange traits ?? If I hear the DSP gremlins getting into a signal I'm really trying to hear right or even more important "record" , and depending how serious it's destroying a signal....I might have to switch over another set. And really why should I have to do this right ?
Reliability, quality of construction , most parts used (with the exception of the VCO trimmer capacitor failures for some owners) and of course the general overall design were all well above any other consumer tabletop set at time this receiver was released on the market. With all of the problems the AOR AR7030 has had over the years (and was until the end of it's production), it's just a more refreshing experience even with the audio (DSP) issues.
I have had my hands on many JRC receivers over the years (including the professional models, see the main page for my review list)
and in our view the NRD-545 "overall" is the king of all JRC
manufactured HF receivers (at the time this report was updated). The
excessively hissy NRD-525 and the NRD-535 with its awful ECSS and other
strange noises , the NRD-545 was a major improvement over those.
Be sure and read the important note in regards with a change made with the AC power transformer in later production in the above text if you have not already. Also covered below is the "mute" issue that as been a problem with some samples (VCO trimmer capacitor failures). These may very well be important for any used NRD-545 purchase ?
c N9EWO, all rights reserved
If you found this review to be enjoyable and useful, please consider a small donation to help keep it here on the internet and updated. ANY donation amount is very much appreciated. Please see the main page for more information. Thank You.
I will NOT be held responsible
for any info that is listed here
A nagging issue that has plagued the Japan Radio Co. NRD-545 over the years has been with the receiver going into a muted state. Either across it's entire range or just certain segments in the HF coverage of the receiver. In some cases when the CHE-199 option board is fitted it fails to operate too (mutes) making it appear that the converter board may be defective (which it still could be in addition to what is covered below ??). Serial numbers that are having this issue seem to be all over the place , right to the end of production in early 2008. It appears that it can happen to any sample that has ever been made ??.
From reading the internet postings over the years on this bug, it appears that one POSSIBLE repair might be with one or more of the 4 plastic case "Murata" VCO trimmer capacitors on the CGA-184 Loop1 Unit that have gone sour ?? This would be CV1, CV2 , CV3 and CV4. Yes, this is just like with many ICOM models over the years that used the same lousy low grade Murata trimmer capacitors in the VCO circuits and elsewhere (models include : IC-745, IC-751 , IC-781, IC-R9000 , IC-970 , IC-275 , IC-475..etc). Sometimes one can rotate these trimmers slightly to make the set come back to life for awhile , but to only fail again later. Other times it's a total lost cause and all 4 should be replaced with a better grade trimmer capacitor. NOTE : The actual Murata trimmer capacitors that were used are no longer made (now discontinued thank goodness). The value is 2.7 to 10 pf . Alignment might be the tricky part of this POSSIBLE repair without the extension board that is almost impossible to obtain , the proper test equipment / service manual and of course the required skill to do it.
I'm not saying this may be the "only" possible repair with any "muting issue" , however it may be a place to start ?? "Caveat Emptor" again for any NRD-545's in the used marketplace......Dave N9EWO
IMPORTANT : I have not had this bug happen to me and what information given here is for general reference only.
c N9EWO, all rights reserved
of the NRD-545.
(Photo Edit : N9EWO)
Dave's JRC NRD-545 Bandwidth Settings
(I changed from "out of the box" settings, "What does Dave use for his preset bandwidth settings ?")
|#||JRC NRD-545 User Defined Functions||Values
(MY Normal Settings in BOLD)
|1.||1 Hz tuning(SSB/CW/RTTY/AM frequency of less than 30 MHz)||0: 1Hz not added to
tuning step OFF
1: 1Hz added to tuning step
|2.||10kHz tuning(SSB/CW/RTTY/AM frequency of less than 30 MHz)||0: 10kHz not added to
1: 10kHz added to tuning step
|3.||1 kHz tuning(SSB/CW/RTTY/AM/FM frequency of less than 30 MHz)||0: 1KHz
3: 9kHz tuning step
|4.||100Hz tuning(FM mode/AM Frequency of more then 30MHz)||0: 100Hz not added to
1: 100Hz added to tuning step
|5.||5kHz tuning(Frequency of more then 30MHz)||0: 5kHz
2: 9kHz tuning step
|6.||10kHz tuning||0: 10kHz
5: 50kHz tuning step
|7.||Tuning step automatic selection||0:Automatic tuning step
1:Automatic tuning step ON
|8.||Number of tuning knob pulses||0: 1000 pulses/turn
1: 500 pulses/turn
2: 250 pulses/turn
|9.||Meter indication||0: Single Display
1: Bar display
2: Peak Hold Display
|10.||Beep tone||0: Beep OFF
1: Beep ON
|11.||Scan auto stop||0: AUTO STOP OFF
1: AUTO STOP ON
|12.||Unwritten channel skip||0: Skip OFF
1: Skip ON
|13.||Timer relay operation||0: Timer relay OFF
1: Timer relay always ON
2: Controled with Squelch
|14.||CW mode BFO offset frequency||-2550 to +2550(Hz) (10 hz
|15.||RTTY baud rate (baud)||37-75(baud) (45)
|16.||RTTY shift width||0: 170Hz
|17.||RTTY polarity||0: Reverse
|18.||SSB display frequency||0: Display shift
1: Local shift
|19.||Display time colon blinking||0: Colon blinking OFF
1: Colon blinking ON
|20.||Scan rate||0.3-5.0(sec.)0.5 sec./CH (0.5)
|21.||Sweep rate||0.05-0.5(sec.) 0.05sec./step (0.05)
|22.||Scan auto stop time setting||0 to 10 seconds (0.5sec.steps) (3.0)|
|23.||RTTY decoding output||0: Do not output
|24.||Input tuning circuit||0: Pass
|25.||RTTY unshift ON space||0: OFF
|26.||RTTY error display||0: Display space
1: * Display
|27.||Filter Hold of Noise Reduction (change in text from earlier manual--was called "Line Enhancer")||0: ON
|28.||Panel lock||0: Lock tuning knob
1: All dials and buttons
|29.||Noise reduction next number change||0.0000 (effect) to 0.0255
(No effect) in 0.0001steps
|30.||Beat canceller next number change||0.0000 (effect) to 0.0255
(No effect) in 0.0001steps
|31.||Squelch LED lighting change||0: Lights when squelch is
1: Lights when squelch is open
|32.||Digital IF Filter setting slope||0: DSP SHARP filter
1: DSP LOOSE filter
"Function" Button Operations
|Changes BWC Encoder Step (either 10 or 100 Hz)|
|Quick toggle of # 24 above "Input tuning circuit", Useful when scanning memories..no relay chattering. (May not work on all samples, unknown ??)|
|Enter User Defined Functions (Above)|
|Memory Channel Save|
|Turn Stereo Mode ON/OFF (FM Wide Mode with CHE-199 Option Installed)|
|Set Sleep Time|
|Transfer Memory Information to VFO|
|PUSH AND HOLD AT POWER UP
(Power OFF and Repeat To Reverse Setting)
"Power Up" User Defined Functions
|Unknown. The the display will show a number like "12 46 13" (varies). Will not receive while in this mode. Just rotating the main tuning knob will restore the set to normal.|
|Toggles "Low End" Receive Range Down To 10 kHz.|
|Allows USB/LSB and CW/RTTY Modes To Be Selected When CHE-199 Converter Is Installed.|
|Memory Channel RESET (WARNING: Clears All Memories) and User Defined Functions To Default Settings.|
|Resets User Defined Functions To Defaults.(Keeps Memory Channels As They Were)|
|Toggles Seconds Display in Clock mode|
|Display Test Mode, entire display lights up. Rotate tuning knob to restore to normal.|
Best "Free" Computer Software for the JRC NRD-545
(link below is subject to change without notice)
are a number of "windows" based computer
programs around for the JRC NRD-545. This the BEST one I
have used (in my view) and it's now freeware . It
requires a "Null Modem" cable or adapter
between the receiver and host computer (as all programs
connected to the NRD-545 do). It does not store the
"tuning step" in the memory channels, so you
will have to do a touch up if you wish that (yes , the
memories on NRD-545 you can store the tuning step on each
memory channel...this is neat indeed).
The "NRD-545 Controller" program from Interfair Laboratory was written by H. Yamamoto in Japan. In was in Japanese only and also required registration with payment. Without it you could only start the program 30 times before it went bye-bye. The authors hard drive crashed and he has lost all source code for the program. Any additional improvements to the software are gone, so he decided to make it "freeware".
J. Schimmele in Germany (with the OK from Mr. Yamamoto), has converted this program to English and is still "freeware". Again I feel it's the best out of lot tested and it allows for memory channels to be either uploaded or downloaded. Follow the instructions, you will have to type in the values shown in the registration as you bring it up for the first time. There is no installation garbage, it just runs in a directory that you place it in. Yes ran OK for me in Windows XP home and PRO, and even Windows 7 "32 or 64 bit" just fine.
IMPORTANT NOTE : THE FUNCTIONALITY OF THE PROGRAM CANNOT BE CHANGED, USE IS "AS IS", AND AT YOUR OWN RISK !! NO WARRANTY OR SUPPORT, YOU ARE TOTALLY ON YOUR OWN ! PLEASE DO NOT ASK ME !
NOTE : SOFTWARE WILL NOT WORK ON "WINDOWS 8 or 10" (sorry) !!
Download English Version "N545Pro" here, zipped size approx 400K
c N9EWO, all rights reserved
The "Sherwood Engineering" Roofing Filter
Via the newsgroups from Jim Valle in regards to the Sherwood Engineering roofing filter modification (NRD-545). I'm actually totally against this modification as it degrades AM audio in wider bandwidths in my testing of a 3rd borrowed sample that had this filter installed. Sorry ! N9EWO
"The 8kHz filter mod has really improved things for me on MW and SW frequencies. Utility monitoring has been GREATLY improved. I have found much less monkey chatter and significantly less spillover from stations close by on all SW bands. The real test is when I listen to utility and can get so much more out of the passband tuning. A perfect example would be listening to AFN in USB. Before the filter replacement there was quite a bit of spill-over from data signals on LSB. This filter along with some narrowing of the filter setting (about 2.2 to 2.4) and using the passband tuning cleans audio up significantly. On MW I have found no noticeable difference in fidelity. I live in an RF rich environment and utilize the Dressler ARA-60 (superb antenna, by the way) so I'm even more impressed by this filter mod. By the way, you only need to send in the board, not the entire rig. Saves on shipping. Bob turns things around very quickly. He is also a very knowledgeable, professional and courteous individual which to deal. All the best, Jim Valle "
Comment below was from when the NRD-545 first hit the market.
had one for about 4 months and I am rather disappointed with it.
In 40 years of SW I've never met a radio which runs out of AF
gain before,but this one does. The 'TONE' control has a very
peculiar action, at one end sound sounds like a telephone, at the
other treble boost. Receiving NAVTEX on 518 causes the AGC and BW
LEDS to flicker in sympathy to signal. VLF gain falls off rapidly
below about 70 kHz. At no settings can I get decent AM reception
with good signal. Awesome it aint."
(I will totally agree with Mike on the NRD-545 "running out of volume control" . But only with under-modulated AM signals. The NRD-301 also suffers from this trait..N9EWO)
Back To Home Page